306438 306436 1357 Die angegebenen Schnittdaten sind eine Empfehlung. Die tatsächlichen Schnittdaten sollten immer an die Bearbeitung und Maschine angepasst werden. Ist die Ihnen zur Verfügung stehende Drehzahl niedriger als die in der Tabelle angegebene, sollte der Vorschub im gleichen Verhältnis reduziert werden. Verwenden Sie ausschließlich stabile und hochgenaue Maschinen. Wir empfehlen beim fräsen in Ecken den Vorschub um ca. 50% zu reduzieren. These conditions are for general guidance; in actual machining conditions adjust the parameters according to your actual machine and workpiece conditions. If the rpm available is lower than recommended please reduce the feed rate to the same ratio. Use only accurate and highly rigid machines. We recommend to reduce the feed rate about 50% when milling in corners. Empfohlene Schnittdaten für VHM-Fräser mit Eckenradius HSC/HHC-beschichtet Recommended cutting data for solid carbide end mills with corner radius HSC/HHC Schruppen Roughing Werkstoffgruppe Material Group 8.1 Gehärtete Stähle / Hardened steels 45 - 55 HRC 8.2-8.3 Gehärtete Stähle / Hardened steels 55 - 70 HRC d1 r min-1 Vf mm/min fz mm ap mm ae mm min-1 Vf mm/min fz mm ap mm ae mm 1 0,1 16.000 1.600 0,025 0,006 0,4 12.000 720 0,015 0,005 0,4 1 0,2 16.000 1.600 0,025 0,008 0,4 12.000 720 0,015 0,005 0,4 2 0,2 13.000 4.160 0,080 0,025 0,8 11.000 1.320 0,030 0,018 0,8 3 0,3 8.500 5.100 0,150 0,050 1,2 7.500 1.500 0,050 0,035 1,2 4 0,2 6.500 5.200 0,200 0,035 1,8 5.500 1.760 0,080 0,025 1,8 4 0,4 6.500 5.200 0,200 0,070 1,6 5.500 1.760 0,080 0,045 1,6 4 0,5 6.500 5.200 0,200 0,090 1,5 5.500 1.760 0,080 0,060 1,5 4 1,0 6.500 5.200 0,200 0,180 1,0 5.500 1.760 0,080 0,120 1,0 5 0,5 5.000 5.000 0,250 0,090 2,0 4.500 1.800 0,100 0,060 2,0 5 1,0 5.000 5.000 0,250 0,180 1,5 4.500 1.800 0,100 0,120 1,5 6 0,2 4.500 5.400 0,300 0,035 2,8 4.000 1.920 0,120 0,025 2,8 6 0,5 4.500 5.400 0,300 0,090 2,5 4.000 1.920 0,120 0,060 2,5 6 1,0 4.500 5.400 0,300 0,180 2,0 4.000 1.920 0,120 0,120 2,0 6 1,5 4.500 5.400 0,300 0,270 1,5 4.000 1.920 0,120 0,180 1,5 8 0,2 3.500 5.600 0,400 0,035 3,8 3.000 1.920 0,160 0,025 3,8 8 0,5 3.500 5.600 0,400 0,090 3,5 3.000 1.920 0,160 0,060 3,5 8 1,0 3.500 5.600 0,400 0,180 3,0 3.000 1.920 0,160 0,120 3,0 8 1,5 3.500 5.600 0,400 0,250 2,5 3.000 1.920 0,160 0,180 2,5 8 2,0 3.500 5.600 0,400 0,350 2,0 3.000 1.920 0,160 0,240 2,0 10 0,2 2.500 5.000 0,500 0,035 4,8 2.500 2.000 0,200 0,025 4,8 10 0,5 2.500 5.000 0,500 0,090 4,5 2.500 2.000 0,200 0,060 4,5 10 1,0 2.500 5.000 0,500 0,180 4,0 2.500 2.000 0,200 0,120 4,0 10 1,5 2.500 5.000 0,500 0,025 3,5 2.500 2.000 0,200 0,180 3,5 10 2,0 2.500 5.000 0,500 0,350 3,0 2.500 2.000 0,200 0,240 3,0 12 0,5 2.000 4.400 0,550 0,090 5,5 2.000 1.840 0,230 0,060 5,5 12 1,0 2.000 4.400 0,550 0,180 5,0 2.000 1.840 0,230 0,120 5,0 12 1,5 2.000 4.400 0,550 0,250 4,5 2.000 1.840 0,230 0,150 4,5 12 2,0 2.000 4.400 0,550 0,350 4,0 2.000 1.840 0,230 0,240 4,0 Schlichten Finishing Werkstoffgruppe Material Group 8.1 Gehärtete Stähle / Hardened steels 45 - 55 HRC 8.2-8.3 Gehärtete Stähle / Hardened steels 55 - 70 HRC d1 r min-1 Vf mm/min fz mm ap mm ae mm min-1 Vf mm/min fz mm ap mm ae mm 1 0,1 25.000 500 0,005 0,02 0,01 20.000 400 0,005 0,02 0,01 1 0,2 25.000 500 0,005 0,02 0,01 20.000 400 0,005 0,02 0,01 2 0,2 14.500 580 0,010 0,05 0,02 11.000 440 0,010 0,05 0,02 3 0,3 9.500 380 0,010 0,05 0,03 7.500 300 0,010 0,05 0,03 4 0,2 7.500 600 0,020 0,05 0,02 7.500 600 0,020 0,05 0,02 4 0,4 7.500 600 0,020 0,05 0,04 7.500 600 0,020 0,05 0,04 4 0,5 7.500 600 0,020 0,05 0,05 7.500 600 0,020 0,05 0,05 4 1,0 7.500 600 0,020 0,05 0,10 7.500 600 0,020 0,05 0,10 5 0,5 6.000 480 0,020 0,05 0,05 4.500 360 0,020 0,05 0,05 5 1,0 6.000 480 0,020 0,05 0,10 4.500 360 0,020 0,05 0,10 6 0,2 5.000 600 0,030 0,10 0,02 4.000 320 0,020 0,10 0,02 6 0,5 5.000 600 0,030 0,10 0,05 4.000 320 0,020 0,10 0,05 6 1,0 5.000 600 0,030 0,10 0,10 4.000 320 0,020 0,10 0,10 6 1,5 5.000 600 0,030 0,10 0,15 4.000 320 0,020 0,10 0,15 8 0,2 3.500 560 0,040 0,10 0,02 3.000 360 0,030 0,10 0,02 8 0,5 3.500 560 0,040 0,10 0,05 3.000 360 0,030 0,10 0,05 8 1,0 3.500 560 0,040 0,10 0,10 3.000 360 0,030 0,10 0,10 8 1,5 3.500 560 0,040 0,10 0,15 3.000 360 0,030 0,10 0,15 8 2,0 3.500 560 0,040 0,10 0,20 3.000 360 0,030 0,10 0,20 10 0,2 3.000 600 0,050 0,10 0,02 2.500 400 0,040 0,10 0,02 10 0,5 3.000 600 0,050 0,10 0,05 2.500 400 0,040 0,10 0,05 10 1,0 3.000 600 0,050 0,10 0,10 2.500 400 0,040 0,10 0,10 10 1,5 3.000 600 0,050 0,10 0,15 2.500 400 0,040 0,10 0,15 10 2,0 3.000 600 0,050 0,10 0,20 2.500 400 0,040 0,10 0,20 12 0,5 2.500 600 0,060 0,10 0,05 2.000 400 0,050 0,10 0,05 12 1,0 2.500 600 0,060 0,10 0,10 2.000 400 0,050 0,10 0,10 12 1,5 2.500 600 0,060 0,10 0,15 2.000 400 0,050 0,10 0,15 12 2,0 2.500 600 0,060 0,10 0,20 2.000 400 0,050 0,10 0,20 10 Index 9 8 OIL 7 MACHINES 6 5 4 3 2 1
RkJQdWJsaXNoZXIy MTgxNTQ=