201925 201925 201427 201439 201925025 201925030 201925035 201925040 201925045 201925050 201925055 201925060 201925065 201925070 201925075 201925080 201925085 201925090 201925095 201925100 201925105 201925110 201925115 201925120 201925125 201925130 201925135 434 ➊ ➋ 1488 • 7,98 × 130 mm ➊ ➋ • 7,98 × 130 mm Weldon Weldon 19 mm 3/4" 80 mm | 3" • mm Art. • 11/16" 17,46 • 3/4" 19,04 • 13/16" 20,63 • 7/8" 22,22 • 15/16" 23,81 • 1" 25,40 • mm Art. • 1.1/16" 26,98 • 1.1/8" 28,57 • 1.3/16" 30,13 • 1.1/4" 31,75 • 1.5/16" 33,33 • 1.3/8" 34,92 • mm Art. • 1.7/16" 36,51 • 1.1/2" 38,10 • 1.9/16" 39,68 • 1.5/8" 41,27 • 1.11/16" 42,86 • 1.3/4" 44,45 • mm Art. • 1.13/16" 46,03 • 1.7/8" 47,62 • 1.15/16" 49,21 • 2" 50,80 • 2.1/16" 52,38 Weitere Informationen erhalten Sie telefonisch unter +49 6203-4039-0 oder schreiben Sie eine Mail an info@karnasch.tools. For more informations please call +49 6203-4039-0 send a mail to info@karnasch.tools. KERNBOHRER • ANNULAR CUTTERS HSS-XE Kernbohrer, Weldonschaft, Nutzlänge 80 mm HSS-XE annular cutter, Weldon shank, drill depth 80 mm | 3" ANWENDUNG AUSWERFERSTIFTE 2-TEILIG APPLICATION EJECTOR PINS 2-PIECE Anwendung: Teil ➊ in den Schaft des Kernbohrers einführen. Teil ➋ auf Teil ➊ schieben. Bohren Sie bis ca. 50 mm Schnitttiefe. Danach Teil ➋ entfernen und weiter bohren. Application: Insert piece ➊ into the annular cutter shank. Push piece ➋ onto part ➊. Drill as deep as 50 mm cutting depth. Then remove piece ➋ and continue drilling. Warum 2-teilige Auswerferstifte? In der Regel haben Standard Morsekonus-Aufnahmehalter eine Schnitttiefenkapazität von 50 mm. Wenn keine extra langen Aufnahmehalter verwendet werden (wie auf Seite 542–543 Art. 20 1842, 20 1291, 20 1843, 20 1845, 20 1846), müssen bei Schnitttiefen über 50 mm 2-teilige Auswerferstifte verwendet werden. Why use 2-part ejector pins? Usually, standard morse taper holders have a cutting depth capacity of 50 mm. If no extra-long holders are used (e.g. as on page 542–543 Art. 20 1842, 20 1291, 20 1843, 20 1845, 20 1846), you need for drill depths above 50 mm 2-part ejector pins. Schnittdaten Cutting data Film Movie AUSWERFERSTIFTE 2-TEILIG EJECTOR PINS 2-PIECE 2-teilig / 2 piece Achtung: Die Zollabmessungen entsprechen nicht exakt den mm Durchmessern. Attention: The inch sizes do not correspond exactly to the mm diameters. Alu Alu Stahl Steel Edelstahl Stainless Kupfer, Messing, Zinn Copper, brass, tin Kunststoffe GFK/CFK Plastics GRP/CRP Grauguss Grey cast iron ANWENDUNG · APPLICATION Zusammen mit Aufnahmehalter 20 1842, 20 1291, 20 1843, 20 1845, 20 1846 (siehe Seite 542–543) kann dieser einteilige Auswerferstift verwendet werden. Es kann ohne Umstecken bis 110 mm Schnitttiefe in einem Arbeitsgang gebohrt werden. Robust und einfach. It is possible to use this one-piece ejector pin in combination with tool holder article 20 1842, 20 1291, 20 1843, 20 1845, 20 1846 (see page 542–543). You can drill as deep as 110 mm in one working process without changing. Robust and easy. AUSWERFERSTIFTE 1-TEILIG · EJECTOR PINS 1-PIECE 1-teilig / 1 piece Zoll/Inch Zoll/Inch Zoll/Inch Zoll/Inch Packnorm 2 Stk. · Packaging unit 2 pcs. Packnorm 2 Stk. · Packaging unit 2 pcs. ZUBEHÖR · ACCESSORIES Hardox 400, 450 Hardox 400, 450 < 900 N < 900 N < 10% Si GOLD-DRILL LINE ZOLL / INCH 80 GOLD-DRILL LINE ZOLL / INCH 80 10 Index 9 8 OIL 7 MACHINES 6 5 4 3 2 1
RkJQdWJsaXNoZXIy MTgxNTQ=