201285N 201285N 201427 201439 201285N018 201285N019 201285N020 201285N021 201285N022 201285N023 201285N024 201285N025 201285N026 201285N027 201285N028 201285N029 201285N030 201285N032 201285N033 201285N035 201285N036 201285N038 201285N040 201285N045 201285N050 490 ➊ ➋ 1488 • 7,98 × 130 mm ➊ ➋ • 7,98 × 130 mm Nitto / Universal Nitto / Universal 19 mm 3/4" 80 mm | 3" Art. • mm 12 0 • 18 45/64" 12 0 • 19 3/4" 12 0 • 20 25/32" 12 0 % 21 53/64" 12 0 • 22 55/64" 12 0 % 23 29/32" Art. • mm 12 0 • 24 15/16" 12 0 % 25 63/64" 12 0 • 26 1.1/32" 12 0 % 27 1.1/16" 12 0 • 28 1.7/64" 12 0 % 29 1.9/64" Art. • mm 12 0 • 30 1.3/16" 12 0 • 32 1.17/64" 12 0 % 33 1.19/64" 12 0 • 35 1.3/8" 12 0 % 36 1.27/64" 12 0 % 38 1.1/2" Art. • mm 12 0 • 40 1.37/64" 12 0 % 45 1.49/64" 12 0 % 50 1.31/32" Weitere Informationen erhalten Sie telefonisch unter +49 6203-4039-0 oder schreiben Sie eine Mail an info@karnasch.tools. For more informations please call +49 6203-4039-0 send a mail to info@karnasch.tools. KERNBOHRER • ANNULAR CUTTERS HSS-XE Kernbohrer, Nitto/Universalschaft, Nutzlänge 80 mm HSS-XE annular cutter, Nitto/Universal shank, drill depth 80 mm | 3" ANWENDUNG AUSWERFERSTIFTE 2-TEILIG APPLICATION EJECTOR PINS 2-PIECE Anwendung: Teil ➊ in den Schaft des Kernbohrers einführen. Teil ➋ auf Teil ➊ schieben. Bohren Sie bis ca. 50 mm Schnitttiefe. Danach Teil ➋ entfernen und weiter bohren. Application: Insert piece ➊ into the annular cutter shank. Push piece ➋ onto part ➊. Drill as deep as 50 mm cutting depth. Then remove piece ➋ and continue drilling. Warum 2-teilige Auswerferstifte? In der Regel haben Standard Morsekonus-Aufnahmehalter eine Schnitttiefenkapazität von 50 mm. Wenn keine extra langen Aufnahmehalter verwendet werden (wie auf Seite 542–543 Art. 20 1842, 20 1291, 20 1843, 20 1845, 20 1846), müssen bei Schnitttiefen über 50 mm 2-teilige Auswerferstifte verwendet werden. Why use 2-part ejector pins? Usually, standard morse taper holders have a cutting depth capacity of 50 mm. If no extra-long holders are used (e.g. as on page 542–543 Art. 20 1842, 20 1291, 20 1843, 20 1845, 20 1846), you need for drill depths above 50 mm 2-part ejector pins. Schnittdaten Cutting data Film Movie AUSWERFERSTIFTE 2-TEILIG EJECTOR PINS 2-PIECE 2-teilig / 2 piece Kleinere ∅ ab 14mm siehe Art. 20 1650N Seite 460 · Achtung: Die Zollabmessungen entsprechen nicht exakt den mm Durchmessern. Smaller ∅ from 14mm see Art. 20 1650N page 460 · Attention: The inch sizes do not correspond exactly to the mm diameters. Alu Alu Stahl Steel Edelstahl Stainless Kupfer, Messing, Zinn Copper, brass, tin Kunststoffe GFK/CFK Plastics GRP/CRP Grauguss Grey cast iron ANWENDUNG · APPLICATION Zusammen mit Aufnahmehalter 20 1842, 20 1291, 20 1843, 20 1845, 20 1846 (siehe Seite 542–543) kann dieser einteilige Auswerferstift verwendet werden. Es kann ohne Umstecken bis 110 mm Schnitttiefe in einem Arbeitsgang gebohrt werden. Robust und einfach. It is possible to use this one-piece ejector pin in combination with tool holder article 20 1842, 20 1291, 20 1843, 20 1845, 20 1846 (see page 542–543). You can drill as deep as 110 mm in one working process without changing. Robust and easy. AUSWERFERSTIFTE 1-TEILIG · EJECTOR PINS 1-PIECE 1-teilig / 1 piece • Zoll Inch • Zoll Inch • Zoll Inch • Zoll Inch Packnorm 2 Stk. · Packaging unit 2 pcs. Packnorm 2 Stk. · Packaging unit 2 pcs. ZUBEHÖR · ACCESSORIES % Sonderpreis / Sale Artikel. Lieferbar solange Vorrat. Special price / sale article. While stocks last. Hardox 400, 450 Hardox 400, 450 < 900 N < 900 N < 10% Si GOLD-DRILL LINE 80 GOLD-DRILL LINE 80 10 Index 9 8 OIL 7 MACHINES 6 5 4 3 2 1
RkJQdWJsaXNoZXIy MTgxNTQ=