201635 201635 201428 201399 Art. 201635025 201635030 201635035 201635040 201635045 201635050 Art. 201635055 201635060 201635065 201635070 201635075 201635080 Art. 201635085 201635090 201635095 201635100 201635105 201635110 Art. 201635115 201635120 201635125 201635130 201635135 500 • mm • 11/16" 17,46 • 3/4" 19,04 • 13/16" 20,63 • 7/8" 22,22 • 15/16" 23,81 • 1" 25,40 • mm • 1.1/16" 26,98 • 1.1/8" 28,57 • 1.3/16" 30,13 • 1.1/4" 31,75 • 1.5/16" 33,33 • 1.3/8" 34,92 • mm • 1.7/16" 36,51 • 1.1/2" 38,10 • 1.9/16" 39,68 • 1.5/8" 41,27 • 1.11/16" 42,86 • 1.3/4" 44,45 • mm • 1.13/16" 46,03 • 1.7/8" 47,62 • 1.15/16" 49,21 • 2" 50,80 • 2.1/16" 52,38 1488 Nitto / Universal Nitto / Universal 19 mm 3/4" 110 mm | 4" ➊ ➋ • 7,98 × 157 mm ➊ ➋ • 7,98 × 160 mm Weitere Informationen erhalten Sie telefonisch unter +49 6203-4039-0 oder schreiben Sie eine Mail an info@karnasch.tools. For more informations please call +49 6203-4039-0 send a mail to info@karnasch.tools. KERNBOHRER • ANNULAR CUTTERS HSS-XE Kernbohrer, Nitto/Universalschaft, Nutzlänge 110 mm HSS-XE annular cutter, Nitto/Universal shank, drill depth 110 mm | 4" Warum 2-teilige Auswerferstifte? In der Regel haben Standard Morsekonus-Aufnahmehalter eine Schnitttiefenkapazität von 50 mm. Wenn keine extra langen Aufnahmehalter verwendet werden (wie auf Seite 542–543 Art. 20 1842, 20 1291, 20 1843, 20 1845, 20 1846), müssen bei Schnitttiefen über 50 mm 2-teilige Auswerferstifte verwendet werden. Why use 2-part ejector pins? Usually, standard morse taper holders have a cutting depth capacity of 50 mm. If no extra-long holders are used (e.g. as on page 542–543 Art. 20 1842, 20 1291, 20 1843, 20 1845, 20 1846), you need for drill depths above 50 mm 2-part ejector pins. Schnittdaten Cutting data Film Movie Achtung: Die Zollabmessungen entsprechen nicht exakt den mm Durchmessern. Attention: The inch sizes do not correspond exactly to the mm diameters. Alu Alu Stahl Steel Edelstahl Stainless Kupfer, Messing, Zinn Copper, brass, tin Kunststoffe GFK/CFK Plastics GRP/CRP Grauguss Grey cast iron ANWENDUNG · APPLICATION Zoll/Inch Zoll/Inch Zoll/Inch Zoll/Inch ZUBEHÖR · ACCESSORIES Hardox 400, 450 Hardox 400, 450 AUSWERFERSTIFTE 2-TEILIG EJECTOR PINS 2-PIECE ANWENDUNG AUSWERFERSTIFTE 2-TEILIG APPLICATION EJECTOR PINS 2-PIECE Anwendung: Teil ➊ in den Schaft des Kernbohrers einführen. Teil ➋ auf Teil ➊ schieben. Bohren Sie bis ca. 50 mm Schnitttiefe. Danach Teil ➋ entfernen und weiter bohren. Application: Insert piece ➊ into the annular cutter shank. Push piece ➋ onto part ➊. Drill as deep as 50 mm cutting depth. Then remove piece ➋ and continue drilling. 2-teilig / 2 piece Zusammen mit Aufnahmehalter 20 1842, 20 1291, 20 1843, 20 1845, 20 1846 (siehe Seite 542–543) kann dieser einteilige Auswerferstift verwendet werden. Es kann ohne Umstecken bis 110 mm Schnitttiefe in einem Arbeitsgang gebohrt werden. Robust und einfach. It is possible to use this one-piece ejector pin in combination with tool holder article 20 1842, 20 1291, 20 1843, 20 1845, 20 1846 (see page 542–543). You can drill as deep as 110 mm in one working process without changing. Robust and easy. AUSWERFERSTIFTE 1-TEILIG · EJECTOR PINS 1-PIECE 1-teilig / 1 piece Packnorm 2 Stk. · Packaging unit 2 pcs. Packnorm 2 Stk. · Packaging unit 2 pcs. < 900 N < 900 N < 10% Si GOLD-DRILL LINE ZOLL / INCH 110 GOLD-DRILL LINE ZOLL / INCH 110 10 Index 9 8 OIL 7 MACHINES 6 5 4 3 2 1
RkJQdWJsaXNoZXIy MTgxNTQ=