211000 610 ➊ ➋ ➍ 1488 ➌ 8 mm 5/16" 13 mm 33/64" • 6-20 mm = • 15/64"-25/32" = • 21-25 mm = • 53/64"-63/64" = Weitere Informationen erhalten Sie telefonisch unter +49 6203-4039-0 oder schreiben Sie eine Mail an info@karnasch.tools. For more informations please call +49 6203-4039-0 send a mail to info@karnasch.tools. EIGENSCHAFTEN · PROPERTIES FUNKTIONSWEISE · OPERATING MODE MINI-LOCHSÄGEN UND SCHWEISSPUNKTFRÄSER MINI-HOLE SAWS AND SPOT WELD CUTTER a. Das Werkstück ankörnen. Es ist wichtig mit dem Körner einen starken Körnerpunkt zu setzen (speziell bei Handmaschinen). b. Setzen Sie den Auswerferstift ➊ genau in die Mitte des starken Körner- punktes an. Zu Beginn des Bohrprozesses wenig Druck (Vorschub) ver- wenden, bis die Lochsäge ca. 0,5 mm Schnitttiefe erreicht hat. Der Bohrer hat sich nun selbst zentriert. Der Vorschub kann erhöht werden. c. Eine Auswurffeder ➋ im Schaft erzeugt Druck auf dem Auswerferstift ➊. d. Zum Einstellen der Schnitttiefe und Federdruck auf dem Auswerferstift drehen Sie die Innensechskantschraube mit dem Innensechskantschlüssel ➌ im Uhrzeigersinn. (Einstellen der Schnitttiefe zum Anbohren von punktgeschweißten Blechen ist nur mit Halter Art. 21 0002 möglich). e. Der Auswerferstift ➊ wirft den Kern ➍ nach dem Durchbohren aus. a. Center punch the workpiece. It is important to set a strong center mark (especially if using handheld machines). b. Place the ejector pin ➊ exactly in the middle of the strong center mark. Use little pressure (feed-rate) until you reach approximately 0,5 mm cutting depth. The drill is self-centered now. Feed rate can be increased. c. An ejector spring ➋ which is installed in the arbor puts pressure on the ejection pin ➊. d. To adjust the cutting depth and spring force turn the Allen screw with the Allen key ➌ clockwise (adjusting the cutting depth for drilling of spot welded sheets is only possible with arbor Art. 21 0002). e. The ejector pin ejects the core ➍ after drilling process. HSS-M2 MINI-CUT Lochsäge für handgeführte Maschinen, Akku-Bohrmaschinen. Das ideale Bohrwerkzeug für: → Elektriker → Sanitär- und Heizungsbauer → Blechbearbeitung → Wartungsinstallationen → Automobile Blechbearbeitung (Schweißpunkte aufbohren) → Und vieles mehr Durch dünne Schnittbreite von nur 2,3 mm → Sehr wenig Schnittdruck für lange Lebensdauer bei Arbeiten mit Akku-Bohrmaschinen. → Keine Verformung dünner Bleche Produziert extrem schnelle, saubere und nahezu gratfreie Bohrungen. Bohrt in dünnste Bleche sowie Platten mit bis zu 13 mm Stärke. Bohrt in Flachmaterial und Rohre aus: → Edelstahl → Stahl → Guss → Bunt- und Leichtmetalle → Kunststoffe HSS-M2 MINI-CUT hole saw for portable machines, cordless drills. The ideal drilling tool for: → Electrical installations → Piping → Conduit work → Sheet metal fabrication → Maintenance installation → HVAC & PHCC → Automotive service (removing spot welds) → And many other industries Because of thin cutting width of only 2,3 mm: → Very little cutting pressure for long battery life if using cordless drilling machines. → No deforming of thin sheet metals Drills clean, almost burr-free holes in seconds. Drills in extremely thin sheet metals as well as in blocks up to 13 mm thickness. Drills in flat material as well as in tubes made of: → Stainless steel → Steel → Cast iron → Non-ferrous metals → Plastics HSS-M2 + TIN beschichtete Lochsäge und Schweisspunktfräser, Nutzlänge 8 + 13 mm HSS-M2 + TIN coated hole saws and spot weld cutter, drill depth 8 + 13 mm | 5/16" + 33/64" Alu Alu Stahl Steel Edelstahl Stainless Kupfer, Messing, Zinn Copper, brass, tin Kunststoffe GFK/CFK Plastics GRP/CRP SandwichMaterial Sandwich materials Grauguss Grey cast iron ANWENDUNG · APPLICATION TIN-GOLD Beschichtung für eine wesentliche Erhöhung der Standzeit auch bei Trockenbearbeitung (ohne/wenig Kühlung). TiN-GOLD coating for considerably longer service life also when machining dry (no/little) cooling. Schnittdaten Cutting data Film Movie < 1100 N > 900 N > 10% Si MINI-CUT 10 Index 9 8 OIL 7 MACHINES 6 5 4 3 2 1
RkJQdWJsaXNoZXIy MTgxNTQ=