306436 306438 1356 Los datos de corte indicados son recomendaciones. Los datos de corte reales se deben ajustar siempre al mecanizado y a la máquina. Si la velocidad de rotación disponible es más baja que la que se indica en la tabla, el avance se deberá reducir en la misma proporción. Utilice exclusivamente máquinas estables y altamente precisas. Al fresar en esquinas, recomendamos reducir el avance alrededor de un 50%. These conditions are for general guidance; in actual machining conditions adjust the parameters according to your actual machine and workpiece conditions. If the rpm available is lower than recommended please reduce the feed rate to the same ratio. Use only accurate and highly rigid machines. We recommend to reduce the feed rate about 50% when milling in corners. Datos de corte recomendados para fresas de metal duro macizo con radio angular y recubrimiento HSC/HHC Desbastado Roughing Grupo de material Material Group 1.1 - 1.2 - 1.3 - 1.4 - 1.5 Aceros no aleados / Unalloyed steels < 850 N/mm² 2.1 - 2.2 - 2.3 - 2.4 - 2.5 - 2.6 - 3.1 - 3.2 Aceros bonificados / Heat treated steels < 35 HRC (1200 N/mm²) 2.1 - 2.2 - 2.3 - 2.4 - 2.5 - 2.6 - 3.1 - 3.2 - 4.1 - 4.2 - 4.3 Aceros bonificados - Aceros inoxidables / Heat treated steels - Stainless steels 35 - 45 HRC d1 r min-1 Vf mm/min fz mm ap mm ae mm min-1 Vf mm/min fz mm ap mm ae mm min-1 Vf mm/min fz mm ap mm ae mm 1 0,1 26.000 3.120 0,03 0,010 0,4 24.000 2.880 0,03 0,010 0,4 20.000 2.000 0,025 0,01 0,4 1 0,2 26.000 3.120 0,03 0,015 0,4 24.000 2.880 0,03 0,015 0,4 20.000 2.000 0,025 0,01 0,4 2 0,2 20.000 8.000 0,10 0,036 0,8 18.000 7.200 0,10 0,036 0,8 16.000 5.120 0,080 0,03 0,8 3 0,3 13.500 10.260 0,19 0,060 1,2 12.000 7.200 0,15 0,060 1,2 10.800 6.480 0,150 0,06 1,2 4 0,2 10.000 10.800 0,27 0,050 1,8 9.000 9.000 0,25 0,050 1,8 8.000 6.400 0,200 0,04 1,8 4 0,4 10.000 10.800 0,27 0,100 1,6 9.000 9.000 0,25 0,100 1,6 8.000 6.400 0,200 0,08 1,6 4 0,5 10.000 10.800 0,27 0,120 1,5 9.000 9.000 0,25 0,120 1,5 8.000 6.400 0,200 0,10 1,5 4 1,0 10.000 10.800 0,27 0,240 1,0 9.000 9.000 0,25 0,240 1,0 8.000 6.400 0,200 0,20 1,0 5 0,5 8.000 9.600 0,30 0,120 2,0 7.000 8.400 0,30 0,120 2,0 6.500 6.500 0,250 0,10 2,0 5 1,0 8.000 9.600 0,30 0,240 1,5 7.000 8.400 0,30 0,240 1,5 6.500 6.500 0,250 0,20 1,5 6 0,2 6.500 10.400 0,40 0,048 2,8 6.000 9.600 0,40 0,048 2,8 5.500 6.600 0,300 0,04 2,8 6 0,5 6.500 10.400 0,40 0,120 2,5 6.000 9.600 0,40 0,120 2,5 5.500 6.600 0,300 0,10 2,5 6 1,0 6.500 10.400 0,40 0,240 2,0 6.000 9.600 0,40 0,240 2,0 5.500 6.600 0,300 0,20 2,0 6 1,5 6.500 10.400 0,40 0,360 1,5 6.000 9.600 0,40 0,360 1,5 5.500 6.600 0,300 0,30 1,5 8 0,2 5.000 11.000 0,55 0,048 3,8 4.500 9.000 0,50 0,048 3,8 4.000 6.400 0,400 0,04 3,8 8 0,5 5.000 11.000 0,55 0,120 3,5 4.500 9.000 0,50 0,120 3,5 4.000 6.400 0,400 0,10 3,5 8 1,0 5.000 11.000 0,55 0,240 3,0 4.500 9.000 0,50 0,240 3,0 4.000 6.400 0,400 0,20 3,0 8 1,5 5.000 11.000 0,55 0,360 2,5 4.500 9.000 0,50 0,360 2,5 4.000 6.400 0,400 0,30 2,5 8 2,0 5.000 11.000 0,55 0,480 2,0 4.500 9.000 0,50 0,480 2,0 4.000 6.400 0,400 0,40 2,0 10 0,2 4.000 11.200 0,70 0,048 4,8 3.500 9.100 0,65 0,048 4,8 3.500 7.000 0,500 0,04 4,8 10 0,5 4.000 11.200 0,70 0,120 4,5 3.500 9.100 0,65 0,120 4,5 3.500 7.000 0,500 0,10 4,5 10 1,0 4.000 11.200 0,70 0,240 4,0 3.500 9.100 0,65 0,240 4,0 3.500 7.000 0,500 0,20 4,0 10 1,5 4.000 11.200 0,70 0,360 3,5 3.500 9.100 0,65 0,360 3,5 3.500 7.000 0,500 0,30 3,5 10 2,0 4.000 11.200 0,70 0,480 3,0 3.500 9.100 0,65 0,480 3,0 3.500 7.000 0,500 0,40 3,0 12 0,5 3.500 11.200 0,80 0,120 5,5 3.000 9.600 0,80 0,120 5,5 3.000 6.600 0,550 0,10 5,5 12 1,0 3.500 11.200 0,80 0,240 5,0 3.000 9.600 0,80 0,240 5,0 3.000 6.600 0,550 0,20 5,0 12 1,5 3.500 11.200 0,80 0,300 4,5 3.000 9.600 0,80 0,300 4,5 3.000 6.600 0,550 0,30 4,5 12 2,0 3.500 11.200 0,80 0,480 4,0 3.000 9.600 0,80 0,480 4,0 3.000 6.600 0,550 0,40 4,0 Acabado Finishing Grupo de material Material Group 1.1 - 1.2 - 1.3 - 1.4 - 1.5 Aceros no aleados / Unalloyed steels <850 N/mm² 2.1 - 2.2 - 2.3 - 2.4 - 2.5 - 2.6 - 3.1 - 3.2 Aceros bonificados / Heat treated steels <35 HRC (1200 N/mm²) 2.1 - 2.2 - 2.3 - 2.4 - 2.5 - 2.6 - 3.1 - 3.2 - 4.1 - 4.2 - 4.3 Aceros bonificados - Aceros inoxidables / Heat treated steels - Stainless steels 35 - 45 HRC d1 r min-1 Vf mm/min fz mm ap mm ae mm min-1 Vf mm/min fz mm ap mm ae mm min-1 Vf mm/min fz mm ap mm ae mm 1 0,1 40.000 1.600 0,01 0,02 0,01 35.000 840 0,006 0,02 0,01 30.000 720 0,006 0,02 0,01 1 0,2 40.000 1.600 0,01 0,02 0,01 35.000 840 0,006 0,02 0,01 30.000 720 0,006 0,02 0,01 2 0,2 30.000 2.400 0,02 0,05 0,02 25.000 1.000 0,010 0,05 0,02 20.000 800 0,010 0,05 0,02 3 0,3 19.000 2.280 0,03 0,06 0,03 16.000 1.280 0,020 0,05 0,03 13.000 1.040 0,020 0,05 0,03 4 0,2 14.500 2.320 0,04 0,10 0,02 12.000 1.440 0,030 0,05 0,02 10.000 800 0,020 0,05 0,02 4 0,4 14.500 2.320 0,04 0,10 0,04 12.000 1.440 0,030 0,05 0,04 10.000 800 0,020 0,05 0,04 4 0,5 14.500 2.320 0,04 0,10 0,05 12.000 1.440 0,030 0,05 0,05 10.000 800 0,020 0,05 0,05 4 1,0 14.500 2.320 0,04 0,10 0,10 12.000 1.440 0,030 0,05 0,10 10.000 800 0,020 0,05 0,10 5 0,5 11.500 2.300 0,05 0,10 0,05 10.000 1.600 0,040 0,05 0,05 8.000 960 0,030 0,05 0,05 5 1,0 11.500 2.300 0,05 0,10 0,10 10.000 1.600 0,040 0,05 0,10 8.000 960 0,030 0,05 0,10 6 0,2 9.500 2.280 0,06 0,20 0,02 8.000 1.600 0,050 0,10 0,02 6.500 1.040 0,040 0,10 0,02 6 0,5 9.500 2.280 0,06 0,20 0,05 8.000 1.600 0,050 0,10 0,05 6.500 1.040 0,040 0,10 0,05 6 1,0 9.500 2.280 0,06 0,20 0,10 8.000 1.600 0,050 0,10 0,10 6.500 1.040 0,040 0,10 0,10 6 1,5 9.500 2.280 0,06 0,20 0,15 8.000 1.600 0,050 0,10 0,15 6.500 1.040 0,040 0,10 0,15 8 0,2 7.500 2.400 0,08 0,20 0,02 6.000 1.440 0,060 0,10 0,02 5.000 1.000 0,050 0,10 0,02 8 0,5 7.500 2.400 0,08 0,20 0,05 6.000 1.440 0,060 0,10 0,05 5.000 1.000 0,050 0,10 0,05 8 1,0 7.500 2.400 0,08 0,20 0,10 6.000 1.440 0,060 0,10 0,10 5.000 1.000 0,050 0,10 0,10 8 1,5 7.500 2.400 0,08 0,20 0,15 6.000 1.440 0,060 0,10 0,15 5.000 1.000 0,050 0,10 0,15 8 2,0 7.500 2.400 0,08 0,20 0,20 6.000 1.440 0,060 0,10 0,20 5.000 1.000 0,050 0,10 0,20 10 0,2 6.000 2.400 0,10 0,20 0,02 5.000 1.600 0,080 0,10 0,02 4.000 960 0,060 0,10 0,02 10 0,5 6.000 2.400 0,10 0,20 0,05 5.000 1.600 0,080 0,10 0,05 4.000 960 0,060 0,10 0,05 10 1,0 6.000 2.400 0,10 0,20 0,10 5.000 1.600 0,080 0,10 0,10 4.000 960 0,060 0,10 0,10 10 1,5 6.000 2.400 0,10 0,20 0,15 5.000 1.600 0,080 0,10 0,15 4.000 960 0,060 0,10 0,15 10 2,0 6.000 2.400 0,10 0,20 0,20 5.000 1.600 0,080 0,10 0,20 4.000 960 0,060 0,10 0,20 12 0,5 5.000 2.200 0,11 0,20 0,05 4.000 1.440 0,090 0,10 0,05 3.500 980 0,070 0,10 0,05 12 1,0 5.000 2.200 0,11 0,20 0,10 4.000 1.440 0,090 0,10 0,10 3.500 980 0,070 0,10 0,10 12 1,5 5.000 2.200 0,11 0,20 0,15 4.000 1.440 0,090 0,10 0,15 3.500 980 0,070 0,10 0,15 12 2,0 5.000 2.200 0,11 0,20 0,20 4.000 1.440 0,090 0,10 0,20 3.500 980 0,070 0,10 0,20 10 Index 9 8 OIL 7 MACHINES 6 5 4 3 2 1
RkJQdWJsaXNoZXIy MTgxNTQ=