306276 1360 Valores orientativos para el uso de la fresa de metal duro macizo con forma de barril de Karnasch Recommended cutting data for solid carbide Karnasch parabola end mills Los datos de corte indicados son recomendaciones. Los datos de corte reales se deben ajustar siempre al mecanizado y a la máquina. Si la velocidad de rotación disponible es más baja que la que se indica en la tabla, el avance se deberá reducir en la misma proporción. Utilice exclusivamente máquinas estables y altamente precisas. These conditions are for general guidance; in actual machining conditions adjust the parameters according to your actual machine and workpiece conditions. If the rpm available is lower than recommended please reduce the feed rate to the same ratio. Use only accurate and highly rigid machines. Fresas con radio efectivo r3 Cutting conditions for arc radius r3 Grupo de material Material Group 2.1 - 2.2 - 2.3 - 2.4 - 2.5 - 2.6 - 3.1 - 3.2 Aceros bonificados / Heat treated steels < 35 HRC (1200 N/mm²) 2.1 - 2.2 - 2.3 - 2.4 - 2.5 - 2.6 - 3.1 - 3.2 - 4.1 - 4.2 - 4.3 Aceros bonificados - Aceros inoxidables / Heat treated steels – Stainless steels 35 - 45 HRC d4 r1 r3 a/2 min-1 Vf mm/min fz mm ap mm ae mm min-1 Vf mm/min fz mm ap mm ae mm 2,50 0,50 12,5 10,17° 24.000 2.880 0,03 0,22 0,05-0,1 19.000 2.280 0,030 0,22 0,05-0,1 5,00 0,50 350 12,60° 12.000 2.400 0,05 1,18 0,05-0,1 10.500 2.100 0,050 1,18 0,05-0,1 3,75 0,75 18,75 10,19° 16.000 2.560 0,04 0,27 0,05-0,1 14.000 2.520 0,045 0,27 0,05-0,1 5,00 1,00 25 10,18° 12.000 2.400 0,05 0,32 0,05-0,1 10.500 2.100 0,050 0,32 0,05-0,1 7,00 1,00 350 13,39° 8.000 1.920 0,06 1,18 0,05-0,1 7.000 1.680 0,060 1,18 0,05-0,1 7,50 1,50 37,5 10,18° 8.000 1.920 0,06 0,39 0,05-0,1 7.000 1.680 0,060 0,39 0,05-0,1 10,00 2,00 50 10,18° 6.000 1.680 0,07 0,45 0,05-0,1 5.000 1.400 0,070 0,45 0,05-0,1 9,00 2,00 350 12,16° 6.000 1.680 0,07 1,18 0,05-0,1 5.000 1.400 0,070 1,18 0,05-0,1 Fresas con radio de la esfera r1 Cutting conditions for ball radius r1 Grupo de material Material Group 2.1 - 2.2 - 2.3 - 2.4 - 2.5 - 2.6 - 3.1 - 3.2 Aceros bonificados / Heat treated steels < 35 HRC (1200 N/mm²) 2.1 - 2.2 - 2.3 - 2.4 - 2.5 - 2.6 - 3.1 - 3.2 - 4.1 - 4.2 - 4.3 Aceros bonificados - Aceros inoxidables / Heat treated steels – Stainless steels 35 - 45 HRC d4 r1 r3 a/2 min-1 Vf mm/min fz mm ap mm ae mm min-1 Vf mm/min fz mm ap mm ae mm 2,50 0,50 12,5 10,17° 34.500 2.484 0,018 0,09 0,30 28.500 2.052 0,018 0,08 0,25 5,00 0,50 350 12,60° 34.500 2.484 0,018 0,09 0,30 28.500 2.052 0,018 0,08 0,25 3,75 0,75 18,75 10,19° 25.500 2.856 0,028 0,10 0,30 21.500 2.150 0,025 0,09 0,25 5,00 1,00 25 10,18° 22.000 3.080 0,035 0,19 0,55 18.500 2.590 0,035 0,15 0,45 7,00 1,00 350 13,39° 22.000 3.080 0,035 0,19 0,55 18.500 2.590 0,035 0,15 0,45 7,50 1,50 37,5 10,18° 20.500 3.280 0,040 0,28 0,85 17.000 2.584 0,038 0,24 0,70 10,00 2,00 50 10,18° 15.500 2.790 0,045 0,38 1,15 13.000 2.340 0,045 0,32 0,95 9,00 2,00 350 12,16° 15.500 2.790 0,045 0,38 1,15 13.000 2.340 0,045 0,32 0,95 Fresas con radio de la esfera r1 y radio efectivo r3 Cutting conditions for ball radius r1 and arc radius r3 Grupo de material Material Group 2.1 - 2.2 - 2.3 - 2.4 - 2.5 - 2.6 - 3.1 - 3.2 Aceros bonificados / Heat treated steels <35 HRC (1200 N/mm²) 2.1 - 2.2 - 2.3 - 2.4 - 2.5 - 2.6 - 3.1 - 3.2 - 4.1 - 4.2 - 4.3 Aceros bonificados - Aceros inoxidables / Heat treated steels – Stainless steels 35 - 45 HRC d4 r1 r3 a/2 min-1 Vf mm/min fz mm min-1 Vf mm/min fz mm 2,50 0,50 12,5 10,17° 29.000 2.900 0,025 24.000 2.208 0,023 5,00 0,50 350 12,60° 17.000 2.720 0,040 14.500 2.320 0,040 3,75 0,75 18,75 10,19° 20.500 2.706 0,033 17.500 2.100 0,030 5,00 1,00 25 10,18° 17.000 2.720 0,040 14.500 2.320 0,040 7,00 1,00 350 13,39° 14.000 2.520 0,045 12.000 2.160 0,045 7,50 1,50 37,5 10,18° 14.000 2.520 0,045 12.000 2.160 0,045 10,00 2,00 50 10,18° 11.000 2.420 0,055 9.000 1.800 0,050 9,00 2,00 350 12,16° 11.000 2.420 0,055 9.000 1.800 0,050 La profundidad y la anchura de corte (ap+ae) se pueden consultar en la tabla de arriba, según la aplicación. For cutting depth and cutting width (ap+ae) refere to the above conditions for each section. La profundidad de corte (ap) depende de la profundidad de la rugosidad teórica (Rth) que se quiera conseguir. Cutting depth ap based on the desired theoretical roughness depth Rth Profundidad de la rugosidad teórica (Rth) en mm Theoretical roughness depth Rth (mm) Art. Radio de la parábola 0,0001 mm 0,0003 mm 0,0005 mm 0,001 mm 0,003 mm 0,005 mm ap mm ap mm ap mm ap mm ap mm ap mm 30 6276 0250 0125 10 12,5 0,10 0,17 0,22 0,32 0,55 0,71 30 6276 0500 350 175 350 0,53 0,92 1,18 1,67 2,90 3,74 30 6276 0375 01875 15 18,75 0,12 0,21 0,27 0,39 0,67 0,87 30 6276 0500 025 20 25 0,14 0,24 0,32 0,45 0,77 1,00 30 6276 0700 350 175 350 0,53 0,92 1,18 1,67 2,90 3,74 30 6276 0750 0375 30 37,5 0,17 0,30 0,39 0,55 0,95 1,22 30 6276 1000 050 40 50 0,20 0,35 0,45 0,63 1,10 1,41 30 6276 0900 350 175 350 0,53 0,92 1,18 1,67 2,90 3,74 10 Index 9 8 OIL 7 MACHINES 6 5 4 3 2 1
RkJQdWJsaXNoZXIy MTgxNTQ=